2010 Jeep Wrangler JK ABS Control Module 68067458 | VIN Programmed
- Regular price $1,600.00
-
--22%
- 4 available
Couldn't load pickup availability
Lifetime Warranty
Reliable support you can trust
Free Shipping
Throughout the USA
Best Prices
In The Market
15 Years In Business
30,000+ Customers Served
In-House Experts
Hablamos Español
2010 Jeep Wrangler JK ABS Control Module 68067458 | VIN Programmed
2010 Jeep Wrangler ABS Control Module – 68067458AA
VIN Programmed | Remanufactured ABS Control Module | ABS Initialization Required
Replace a malfunctioning anti-lock braking system controller with the 2010 Jeep Wrangler ABS Control Module 68067458AA.
This remanufactured ABS control module is advertised for select 2010 Jeep Wrangler JK vehicles experiencing ABS warning lights, traction control problems, communication faults, or other issues involving the anti-lock braking system.
The ABS control module processes wheel speed information and helps coordinate anti-lock braking functions. Depending on factory equipment, it may also support traction control and electronic stability control.
VIN PROGRAMMED FOR YOUR VEHICLE
IMPORTANT: ABS INITIALIZATION IS REQUIRED AFTER INSTALLATION.
Key Features
-
Advertised Vehicle: 2010 Jeep Wrangler
-
Vehicle Generation: Jeep Wrangler JK
-
Primary Part Number: 68067458AA
-
Component Type: Anti-Lock Brake System (ABS) Control Module
-
Condition: Remanufactured
-
VIN Programming: Programmed using your vehicle's supplied VIN before shipping
-
ABS Initialization: Required after installation
-
Anti-Lock Braking: Supports applicable factory ABS functions
-
Traction Control: Supports applicable factory-equipped systems
-
Fitment Verification: Required before ordering
Vehicle Compatibility
2010 Jeep Wrangler JK
-
2010 Jeep Wrangler — select configurations
Compatibility may depend on:
-
Original ABS module part number
-
Vehicle trim and equipment
-
Two-door or four-door configuration
-
Factory braking system configuration
-
Vehicle VIN
Important: Not every 2010 Jeep Wrangler necessarily uses the same ABS control module.
Compatibility with every trim level or factory braking system configuration has not been independently verified.
Verify your original ABS module part number and VIN before ordering.
Part Numbers and Cross-References
Primary Part Number
-
68067458AA
Additional Part Numbers Shown in the Supplied Product Image Reference
-
68284715AA
-
68304562AA
The supplied image reference identifies 68284715AA, 68304562AA, and 68067458AA together.
However, the source does not establish that these three numbers are interchangeable or that the additional numbers fit every 2010 Jeep Wrangler.
Important: Confirm compatibility using your original ABS module part number and vehicle VIN before ordering.
Remanufactured ABS Control Module
This replacement ABS control module is identified as a remanufactured unit.
Remanufacturing involves servicing an existing automotive electronic component for reuse.
A compatible remanufactured module may provide an alternative to purchasing a new replacement component.
The exact inspection, repair, and testing procedures for this individual unit have not been independently verified.
VIN Programming
This ABS control module is VIN programmed for your vehicle before shipping using the VIN supplied with your order.
Required Vehicle Information
-
17-digit VIN
-
Vehicle year and model
-
Original ABS module part number
-
Vehicle configuration and equipment
-
Stored diagnostic trouble codes, if available
IMPORTANT: THE MODULE IS PRE-PROGRAMMED, BUT ABS INITIALIZATION IS STILL REQUIRED AFTER INSTALLATION.
ABS Initialization Required After Installation
ABS INITIALIZATION MUST BE PERFORMED AFTER INSTALLING THIS MODULE.
Although the replacement module is programmed before shipping, the supplied product instructions explicitly require ABS initialization after installation.
A qualified automotive technician should use compatible diagnostic equipment to perform the required vehicle-specific procedure.
Depending on the repair, additional configuration, calibration, or hydraulic system bleeding may also be necessary.
Do not assume this module is plug-and-play.
The braking system must be checked for correct operation before the vehicle is returned to service.
Common 2010 Jeep Wrangler ABS Module Problems
A malfunctioning ABS control module may be associated with:
-
ABS warning light illuminated
-
Traction control warning light illuminated
-
Electronic Stability Control warning
-
ABS pump running continuously
-
ABS pump motor-related faults
-
Intermittent ABS operation
-
No communication with the ABS module
-
Diagnostic scanner communication failures
-
Intermittent electrical power loss
-
Internal ABS control module faults
-
ABS solenoid valve-related faults
-
Wheel speed sensor-related diagnostic codes
-
Wheel speed sensor-related warning lights
-
Intermittent or inaccurate speedometer readings
-
Speedometer not functioning
-
Loss of anti-lock braking functionality
Diagnostic Note: These symptoms can also result from faulty wheel speed sensors, damaged wiring, low battery voltage, poor electrical connections, or other braking system components.
An ABS fault does not necessarily indicate an engine control problem.
Proper diagnosis is recommended before replacing the ABS module.
Common ABS Diagnostic Trouble Codes
The following codes were supplied as diagnostic references for this product listing.
C2116 – ABS Pump Motor Fault / Pump Supply Low Voltage
May indicate an ABS pump motor circuit problem or insufficient electrical supply voltage.
C2200 – Anti-Lock Brake Module Internal Fault
May indicate an internal electronic malfunction within the ABS control module.
C2200-49 – Anti-Lock Brake Module Internal Electronic Fault
May identify an internal electronic fault in applicable ABS systems.
U0121 – Lost Communication with ABS Module
Generally indicates that another vehicle control module has lost communication with the ABS controller.
Important: These codes do not independently confirm that part number 68067458AA has failed. Vehicle-specific diagnostic procedures should be followed before replacing the module.
ABS Control Module Functions
Depending on factory equipment, the ABS control module supports:
-
Anti-lock braking
-
Wheel speed monitoring
-
Hydraulic brake pressure regulation
-
Traction control
-
Electronic stability control
-
ABS fault monitoring
The ABS system helps reduce wheel lockup during hard braking and supports vehicle control in low-traction conditions.
Installation Information
Professional installation by a qualified automotive technician is recommended.
Installation Overview
-
Verify the original ABS module part number.
-
Install the compatible replacement ABS control module.
-
Confirm VIN programming and vehicle configuration.
-
Perform the required ABS initialization procedure.
-
Complete any additional required calibration or setup.
-
Bleed the hydraulic brake system if necessary.
-
Clear stored diagnostic trouble codes.
-
Verify ABS, traction control, and stability control operation.
Important: The supplied product information identifies an ABS control module but does not establish whether the product includes the electronic controller alone or a complete hydraulic pump assembly.
Confirm the included components before ordering.
ABS INITIALIZATION IS REQUIRED AFTER INSTALLATION.
Always verify proper braking system operation before returning the vehicle to service.
Frequently Asked Questions
1. Will ABS module 68067458AA fit my 2010 Jeep Wrangler?
It is advertised for select 2010 Jeep Wrangler vehicles. Confirm compatibility using your VIN and original ABS module part number.
2. What is the full ABS module part number?
The primary part number is 68067458AA.
3. Is this ABS module compatible with the 2010 Jeep Wrangler JK?
The product is advertised for the 2010 Jeep Wrangler, which belongs to the JK generation. Exact fitment requires verification.
4. Does this module fit both two-door and four-door Wranglers?
Compatibility with both configurations has not been independently established.
5. Is 68284715AA interchangeable with 68067458AA?
Both numbers appear in the supplied image reference, but interchangeability has not been verified.
6. Is 68304562AA compatible with 68067458AA?
The supplied image reference associates these numbers, but compatibility must be confirmed before ordering.
7. Is this ABS module remanufactured?
Yes. The supplied product information identifies it as a remanufactured ABS control module.
8. Is this ABS module VIN programmed?
Yes. The module is programmed using your vehicle's supplied VIN before shipping.
9. Do I need to provide my VIN?
Yes. Your 17-digit VIN is required for programming.
10. Is ABS initialization required after installation?
Yes. ABS initialization is required after installation, even though the module is pre-programmed.
11. Is this ABS module plug-and-play?
No plug-and-play installation should be assumed. The supplied instructions explicitly require ABS initialization.
12. Can a faulty ABS module cause the traction control light to illuminate?
Yes. ABS system faults may affect applicable traction control and electronic stability control functions.
13. What does C2116 mean?
It may indicate an ABS pump motor circuit fault or insufficient pump supply voltage.
14. What does C2200 mean?
It may indicate an internal ABS control module fault.
15. What does U0121 mean?
It generally indicates lost communication with the ABS control module.
Order Your 2010 Jeep Wrangler ABS Control Module
Get your 2010 Jeep Wrangler ABS Control Module 68067458AA, remanufactured and VIN programmed for your vehicle.
VIN Programmed | Remanufactured ABS Module | Select 2010 Jeep Wrangler Applications
Before ordering:
-
Verify your original ABS module part number.
-
Provide your 17-digit VIN.
-
Confirm your vehicle's braking system configuration.
-
Arrange for required ABS initialization after installation.
IMPORTANT: ABS INITIALIZATION REQUIRED AFTER INSTALLATION.
Looking for a Different Module?
Search by part number, year, make, model, engine / platform, or module type.